News

Flammability Test Apparatus, Burning Tests Flammability Tests: Comprehensive Fire Safety Assessment Tools Automotive interior combustion testing instruments are widely used in the automotive industry. Major car manufacturers and interior suppliers use these instruments to test and evaluate the fire resistance of their products. By using these instruments, the combustion characteristics of materials can be better understood, ensuring optimal safety in the event of a fire.   Testing Standards and Requirements Different countries and regions have corresponding standards and requirements for the combustion and flammability testing of automotive interior materials.     Compliance Standards: 1. Chinese Standard GB8410-2006 (Combustion Characteristics of Automotive Interior Materials) 2. International Standard ISO 3795 (Road Vehicles—Determination of Burning Behaviour of Interior Materials) 3. EU Standard 95/28/EC Annex IV (Test for Horizontal Burning Rate of Materials Used in the Interior Construction of Certain Categories of Motor Vehicles) 4. U.S. Standard SAE J 369 a 5. U.S. Standard FMVSS 571.302 6. Japanese Standard JIS D1201 7. German Standard DIN 75200 8. Volkswagen Standard TL-VW 1010 9. French Standard NF R18-501 10. Korean Standard MS 300-08 11. Mercedes-Benz Standard DBL 5310 12. BMW Standard GS97038   The purpose of this test is to determine the combustion characteristics of materials when exposed to flame, and to measure parameters such as burning rate, flame spread path, and smoke production. These parameters help assess the fire resistance of materials, enabling the design of safer automotive interiors.   Automobile interior combustion test instrument manufactured by YUWEI. Structure and Functionality: l Components:  1. Control box 2. Combustion chamber 3. Burner 4. Solenoid valve (flowmeter) 5. High-voltage igniter 6. Thermometer 7. Signal control lines 8. Upper and lower sample holders 9. Optional ventilation hood l Materials and Appearance: 1. Control box and combustion chamber are made of stainless steel, ensuring easy cleaning, maintenance, aesthetic appeal, and resistance to smoke and gas corrosion. 2. The main combustion chamber is also stainless steel, significantly extending the instrument's lifespan. l Automation Features: 1. Automatic ignition 2. Automatic gas supply 3. Automatic timing 4. Automatic test conclusion l High-Reliability Ignition: 1. Ensures flame stability. l Timing Functions: 1. The combustion time timer can automatically reset. l Safety Design: 1. Electrical and gas systems are housed separately, enhancing operational safety. 2. The combustion chamber has a fireproof glass door for safety. 3. The LPG tank is mounted on a base rack, allowing easy access during tests. 4. The gas safety system features leak detection, alarms, and automatic gas shut-off. l Environmental Protection: 1. The integrated design of the environmental protection chamber fully complies with national standards for test environment volume. 2. The chamber interior is coated with a special heat-resistant, non-stick paint, facilitating cleaning. l Exhaust System: 1. The slow flow device gently releases hot gases and smoke generated during combustion tests, ensuring stability. 2. A high-power exhaust fan rapidly expels smoke after the test. l Sealing: 1. Excellent sealing properties prevent smoke and harmful gases from escaping during tests, protecting operators. l Wind Speed Control: 1. The wind speed adjustment system can automatically control wind speed in real-time, ensuring it remains within national standard requirements throughout the test, ensuring test consistency and compliance. l Real-Time Display: 1. Continuous display of combustion chamber temperature. l Observation Window: 1. Wide-view heat-resistant glass window for easy observation during tests. l Complete Accessories: 1. All necessary accessories for standard horizontal combustion tests of automotive interior materials are included.      

  Compliance Standards: IEC62196-1 Figure 8 (requires customer-provided drawings for customization) Application: To verify whether the maximum force required to withdraw the plug from the socket, and the minimum force required to withdraw a single-pole pin from the pin-and-sleeve assembly, are within the specified standard range.   Testing Purpose: The structure of electrical accessories should allow for easy insertion and withdrawal of the plug, and should prevent the plug from coming out of the socket during normal use.   Test Sample : Charging pile plugs or sockets for similar purposes (longitudinal testing).   Technical Specifications: l Charging Pile Gauges: Two sets l Weights: One set, can be stacked to achieve a 100N withdrawal force test, with additional weights applying 1/10th of the test force l Operation Method: Manual l Providing one safety lanyard to prevent the test plug from falling and getting damaged during use

  An IP (Ingress Protection) test measures the ability of a lighting fixture to resist the intrusion of foreign objects and moisture. This process is used to determine the level of protection the fixture offers against these elements. The results of such tests are typically expressed as an IP rating.   Why is IP Testing for Lighting Fixtures Important?   1. Safety: Improper moisture sealing in lighting fixtures can create safety hazards. Moisture can lead to electric shock and short circuits, potentially causing fires or other accidents.   2. Performance: Poorly sealed lighting fixtures can also degrade performance and efficiency, affecting their overall effectiveness and lifespan.   3. Compliance: Industry standards and regulations often require compliance. Adhering to these standards is crucial to ensure the safety and effectiveness of lighting fixtures.   Steps to Conduct IP Testing for Lighting Fixtures   The testing is conducted according to the national standard GB/T 4208-2017 "Degrees of Protection Provided by Enclosures (IP Code)." 1. Review Specifications: Before conducting the test, review the specifications of the lighting fixture to determine the required IP protection level.   2. Prepare Testing Equipment: Prepare the testing equipment according to applicable standards and regulations.   3. Conduct the Test: The test involves exposing the lighting fixture to water, dust, and other foreign objects to determine its resistance to these intrusions. The duration and intensity of the test depend on the required protection level.   4. Interpret the Results: After completing the test, interpret the results to determine the fixture's IP rating. This rating will indicate the level of protection the fixture offers against foreign objects and moisture.   5. Document the Results: Record the results for future reference. This information can be used to demonstrate compliance with industry standards and regulations.   Dust Test In the dust test, the lighting fixture is placed in a specific dust-proof test chamber, simulating different environmental conditions through various dust concentrations and airflow speeds. After a set period of testing, the fixture is inspected to determine whether any dust has infiltrated the interior.   Water Test In the water test, different spray devices and water pressures are used to conduct a spray test on the fixture. For example, for an IPX5 rating, the fixture must be sprayed with a nozzle having a diameter of 6.3mm, from a distance of 2.5 to 3 meters, with a flow rate of 12.5 liters per minute, for a duration of no less than 3 minutes. During the test, the fixture is observed for any signs of water leakage.    

LVD Test: Under the TS EN / IEC 60335-1 standard, electrical devices that we use in all areas of our lives are critical for safety. In this regard, there are major directives around the world in terms of security experiments. Within the scope of 2014/35 / EU LVD (Low Voltage Directive) directive, TS EN / IEC 60335-1 standard is the main standard of LVD safety test / LVD test of devices used in home and similar places. This standard covers the safety rules of electrical devices used in single-phase devices, operating at rated voltage not exceeding 250 V in others and 480 V in others, used in domestic and similar places and for commercial purposes. 1) Classification 1.1) Devices must have one of the following classes according to their protection against electric shock: Class I, Class II, Class III 1.2) Devices must have a suitable degree of protection (IPXX) against ingress of harmful water. 2) Marking and Instructions Devices should be marked; - With the rated voltage or the rated voltage range in volts, - With the symbol of the feed type, unless marked with the declaration frequency, - With rated input power in watts or rated current in amperes, - With the name, trade mark or identification mark of the manufacturer or responsible dealer, - By model or type reference, - With IEC 60417-5172 (2003-02) symbol for Class II devices only, - According to the degree of protection against harmful water inlet, except IPX0, with IP number - Class III devices  with the IEC 60417-5180 (2003-02) symbol.  3) Protection Against Access to Live Parts Devices should be manufactured and enclosed in a way to provide adequate protection against random contact of the live parts. Compliance with this rule is checked by applying force to the device openings with various test probes such as articulated finger.  4) Power Input and Current The input power declared on the label of the devices should be marked so as not to exceed the deviation values in the table below, depending on the type and operating power of the device. Input Power Deviations Equipment Type Rated Power W Deviation All Types up to 25 + % 20 Including Heating Element > 25 and up to 200 ± % 10 > 200 + % 5 or 20 W (higher is applied) – % 10 Including Motor > 25 and up to 300 + % 20 > 300 + % 15 or 60 W (higher is applied) The current declared on the label of the devices should be marked so as not to exceed the deviation values in the table below, according to the type and operating power of the device.  Current Deviations Equipment Type Rated Current A Deviation All Types up to 0,2 + % 20 Including Heating Element > 0,2 and up to 1,0 ± % 10 > 1,0 + % 5 or 0,10 A (higher is applied) – % 10 Including Motor > 0,2 and up to 1,5 + % 20 > 1,5 + % 15 or 0,30 A (higher is applied)   5) Heating During the operation of the devices at the voltage values specified in the standard, temperature measurements are taken from the points requested by the standard with thermocouples. These temperature values should not exceed the limits in the standard.  6) Leakage Current and Electric Strength at Operating Temperature  The leakage current values that they have spread to their housings during the operation of the devices are checked with the equipment and methods specified in the standard. These leakage current values must be below the limits specified in the standard.The devices are then de-energized from the supply source and a high voltage is applied between the feed ends and the enclosures at the values specified in the standard. There should not be any discharge and puncture between the sections where tension is applied during the test.  7) Moisture Resistance The devices are kept in the humidity cabinet with the relative humidity of 93 ± 3% and the temperature between 20 ° C - 30 ° C for 48 hours. Then leakage currents are measured and electrical resistance test is applied.  8) Abnormal Operation   The components in the device are operated under single error conditions as requested by the standard. During the experiment, the devices should not show conditions such as warming and arc formation that may damage their surroundings.  9) Stability and Mechanical Hazard The equilibrium of the devices that are not fixed on the floor or used on the table should be at a sufficient degree. The devices are tested on the inclined plane at an angle of 10 °. It should not be overturned.  10) Mecanical Strength The devices must be resistant to mechanical impacts that may occur under normal usage conditions. The devices are tested by applying 3 impacts on the same point with the spring hammer whose impact energy is 0.5J on the part with weak mechanical strength.  11) Provision for Earthing The resistance value between the accessible metal enclosures of the devices and the earthing tip must be under 0.1 Ω. The resistance value is calculated from the voltage drop by applying 25 A current between the metal housing and the grounding tip.  12) Screws and Connections The screws used in joining the parts of the devices and electrical connections must be resistant to mechanical forces. Suitability is tested by tightening and loosening the screws at the moments given in the standard according to the thread diameters.  13) Clearances, Creepage Distances and Solid Insulation The insulation ranges and superficial leakage path lengths of the different polarized energy conductors in the devices should be at a distance suitable for the operating voltage. Conformity is measured using tools such as calipers and gauges. 14) Resistance to Heat and Fire The outer sections of the non-metallic material, the sections made of insulating material that support the energetic sections, including connections, must be heat resistant. To verify compliance, ball pressure test, glow wire test and needle flame test are performed at the values specified in the standard.  

Socket Outlet  Refers to the physical interface on the charging station, usually a rectangular or circular port used to supply power.   Plug  The part of the charging cable that connects to the socket outlet on the charging station. Its shape matches the socket outlet to ensure a secure connection and reliable power transfer.   Connector Located at the opposite end of the charging cable, this component connects to the electric vehicle. It is typically designed with a round or multi-edged shape to fit perfectly with the vehicle's inlet.   Vehicle Inlet  This is the physical interface installed on the electric vehicle, used to connect with the charging connector and ensure the vehicle can charge properly.   In some charging systems, the charging cable is permanently attached to the charging station. In these cases, there is no separate socket outlet on the charging station, and the charging cable does not require an independent plug. This design simplifies the charging process, as the connector can be directly inserted into the vehicle inlet to start charging.  

  What is Tracking ? Refers to the process where a conductive path gradually forms on the surface of solid insulation materials under the combined effects of an electric field and an electrolyte. The ability of an insulation material's surface to resist tracking is called tracking resistance.   Purpose of the Tracking Test  1. The primary purpose of the tracking resistance test is to simulate whether conductive substances deposited on the surface of insulation materials due to different polarity charged components in household electrical products during actual use can cause surface creeping, breakdown, short-circuiting, and fire hazards. 2. During use, electrical products may experience leakage current due to contamination and moisture on the insulation material surfaces caused by environmental pollution, which can lead to corrosion and damage to the insulation performance. 3. The test specified in this standard is an accelerated test under simulated extreme conditions to evaluate whether the insulation material will develop tracking marks. This allows for distinguishing the tracking resistance of solid insulation materials within a short period, ensuring the safe use of products under specific environmental conditions.   Scope of Application of the Tracking Test  ü This test applies to research, production, and quality inspection departments of lighting equipment, low-voltage electrical appliances, household appliances, machine tool electrical appliances, motors, power tools, electronic instruments, electrical meters, and information technology equipment. ü It is also applicable to the insulation materials, engineering plastics, and electrical connectors and accessories industries.   Standards for Tracking Test  The tracking test apparatus follows the simulation test procedures specified in IEC 60112: 2003, "Method for Determining the Comparative and Proof Tracking Indices of Solid Insulating Materials."   Here is the good recommendation : Insulation Resistance to Tracking Test Chamber      If you interested in it , don't hesitate to get in touch with us ： Website:  www.yuweiinstrument.com Whatsapp:  +86 17322711289 E-mail:  sales@yuweiinstrument.com    

Why is Plug and Socket Insertion and Withdrawal Testing so Important?   1. Good insertion and withdrawal capability ensure that electrical devices can connect to the power supply stably and reliably. If there is poor contact between the plug and socket, it may result in unstable current transmission, affecting the normal operation of the device, and possibly even damaging the equipment. 2. Poor insertion and withdrawal capability may also lead to electrical fires. During the insertion and withdrawal of plugs and sockets, abnormal phenomena like arc discharge may occur, which can generate high temperatures and ignite surrounding flammable materials. 3. This also concerns our personal safety. Poor contact can cause electric shock accidents, posing a threat to our lives.   Methods for Testing  1. Mechanical Durability Testing: Simulates repeated plug-in and pull-out actions of the plug and socket to test the durability and stability of their mechanical structure. For example, a specific number of insertions and withdrawals are specified to observe whether the plug and socket deform, loosen, or show other signs of wear.   2. Electrical Performance Testing: Measures parameters such as resistance, voltage, and current during the connection and disconnection process to assess the reliability of the electrical connection. For instance, checking whether the contact resistance is within the specified range, as excessive contact resistance can lead to overheating and energy loss.   3. Temperature Rise Testing: Measures the temperature increase after a certain period of connection and disconnection of the plug and socket. If the temperature rise is too high, it indicates potential safety hazards.    Who Needs Testing Instruments? 1. Quality Inspection Agencies: They need to accurately measure key indicators such as the number of insertions and withdrawals, contact resistance, and temperature rise of plugs and sockets to determine whether they meet relevant national standards and industry regulations. 2. Manufacturers: They are responsible for ensuring that the plugs and sockets they produce strictly comply with standards in terms of insertion and withdrawal capability. Manufacturers need to invest sufficient resources to purchase testing equipment.   Plug and Socket Plugging and Unplugging On-Off Capacity Test Equipment      If you interested in it , don't hesitate to get in touch with us for know more detail and pricing .   Website:  www.yuweiinstrument.com Whatsapp:  +86 17322711289 E-mail:  sales@yuweiinstrument.com    

  Why is microwave oven door durability testing so important?   1. The microwaves generated during the operation of a microwave oven are a powerful form of energy. If the microwave oven door cannot maintain good sealing over long-term use, the risk of microwave leakage increases significantly. Microwave leakage can pose potential health risks, such as causing headaches, dizziness, and impaired vision.   2. For instance, there have been reports where a certain brand's microwave oven, due to poor door durability, experienced microwave leakage after a period of use, leading to discomfort among users. This incident clearly illustrates the importance of microwave oven door durability testing.   3. Frequent opening and closing of the microwave oven door is common in daily use. After long-term repeated operation, if the structure and component quality of the door are inadequate, failures such as the door not closing properly, door lock damage, and hinge breakage may occur. These issues not only affect the normal use of the microwave oven but can also lead to uneven heating and energy waste.   4. For manufacturers, microwave oven door durability testing is crucial to ensuring product quality and maintaining brand reputation. Through rigorous testing, weaknesses in product design and manufacturing processes can be identified and timely improvements and optimizations can be made, enhancing the product's reliability and stability. Additionally, good durability can increase consumer trust and loyalty to the brand.   5. Suppose a microwave oven manufacturer neglects door durability testing in order to cut costs, leading to widespread product issues with door quality in the market. This would not only result in significant after-sales repair and return costs but would also severely damage the company's image and market share.   Our Company Offers Testing Products: Microwave Oven Door Durability Tester Used for mechanical durability testing of the microwave oven door system, including hinges, microwave seals, and other related components.   If you interested in it , don't hesitate to get in touch with us for know more detail and pricing  Website:  www.yuweiinstrument.com Whatsapp:  +86 17322711289 E-mail:  sales@yuweiinstrument.com

In our daily lives and work, the use of electrical appliances is ubiquitous. As a key component that connects appliances to power sources, the safety of plugs (pins) is crucial. Among these, the wear resistance of the insulation sleeve on plugs (pins) is an important factor in ensuring electrical safety.   What is Wear Resistance Testing for Plug Insulation Sleeves? Wear resistance testing for plug insulation sleeves is a specialized test designed to assess the sleeve’s ability to withstand wear and tear during everyday use. By simulating scenarios such as plugging and unplugging, friction, and other actual usage conditions, this test evaluates whether the insulation sleeve can maintain good insulating performance over time, preventing electric shock accidents.   Why is this Testing Necessary? 1. Ensuring User Safety With frequent plugging and unplugging, the insulation sleeve may become thin or even damaged due to wear. Once the insulation sleeve loses its protective function, the internal conductive parts may be exposed, increasing the risk of electric shock. Conducting wear resistance tests ensures that the insulation sleeve can withstand long-term use, providing reliable safety for users.For example, there was a case where a resident was using an old appliance, and due to severe wear on the plug’s insulation sleeve, they accidentally touched the internal conductive parts while plugging in, resulting in an electric shock injury. 2. Improving Product QualityFor appliance manufacturers, performing wear resistance tests on plug insulation sleeves allows for strict quality control of their products. Only plugs that pass this test can be sold on the market, enhancing the brand’s reputation and market competitiveness.A well-known appliance brand, which strictly adhered to wear resistance testing standards during production, received high consumer recognition and saw continuous sales growth. In contrast, a smaller manufacturer that neglected this testing faced multiple safety incidents related to worn insulation sleeves shortly after their products were launched, ultimately damaging the company’s reputation and leading to its closure.   3. Compliance with Regulatory StandardsIn many countries and regions, there are regulations and standards requiring plugs (pins) to pass a certain level of wear resistance testing. This is to ensure public electrical safety and maintain market order. Companies must comply with these regulations to legally produce and sell electrical products.There was an instance where a company was fined heavily and required to recall all non-compliant products after its plugs failed wear resistance testing, resulting in significant financial losses.   How is Wear Resistance Testing Conducted? l Typically, wear resistance testing is carried out using specialized testing equipment, which subjects the insulation sleeve of the plug to repeated friction and wear. l Testing parameters include the number of wear cycles, wear force, and wear speed. l After a series of tests, the wear degree and insulation performance of the sleeve are evaluated.   Our company recommends this Plug Insulation Sleeve Wear Resistance Tester    

                                Why is it necessary?    Electrical issues in appliances can lead to fire hazards or the risk of electric shock. Without proper testing and maintenance, even appliances like refrigerators or dishwashers can be dangerous.    Types of Appliance Testing    Appliance testing can be divided into two main categories: hot testing and cold testing. Hot testing: Tests conducted while the device is powered on. Cold testing: Tests conducted while the device is unplugged.   Steps of Appliance Testing    During electrical testing of appliances, professionals typically measure three different electrical parameters: continuity, voltage, and current.   Safety First:  Avoid touching any electrical components with your skin, don't touch the metal tips of the multimeter leads, and don't allow the multimeter leads to touch each other. Electrical testing is the work of experienced professionals.   1.Continuity 1. First, unplug the appliance and disconnect it from any water or gas pipes. 2. Set the multimeter to the "ohm" function. 3. Now, test the electrical continuity of switches, thermostats, and other contacts that should be closed. To do this, touch one end of the multimeter lead to the terminal (the contact point of the component) and the other end to the opposite contact point. 4. If the closed contacts have good conductivity, the reading should be 2 ohms or less. If the reading is higher than 2 ohms, the electrical controller you are testing may need to be replaced. 5. For components other than those mentioned above, the resistance should vary. Refer to the manufacturer's manual to ensure you are looking for the correct ohm reading.   2.Voltage 1. After confirming that the outlet voltage is safe, you can proceed with these steps. 2. First, ensure the appliance is turned off and plugged in. 3. To check if voltage is flowing "downstream" from the outlet into the appliance, set the multimeter to the AC voltage setting. 4. Turn off the appliance, and then touch the circuit with the multimeter probes to read the voltage. 5. The target voltage depends on the type of appliance you have and the component you are testing. 6. When testing the voltage of a dryer heating element, stove, or furnace element, look for 240V AC. 7. When testing the control voltage on 120V appliances for solenoids, timers, and other components, look for 120V AC. 8. If the voltage reading is below normal, one of the following issues might be present: Circuit problem: Typically a switch or thermostat is open or has poor conductivity. Poor wire connection: Check if wires are burned or discolored.   3.Amperage  Testing amperage or current is another way to check continuity. The main difference is that amperage testing is done while the appliance is plugged in. 1. Set the multimeter to the "amp" range (A), not the "milliamp" range. 2. Turn off the appliance and connect the multimeter to the circuit to be tested. 3. Turn the appliance back on and get a reading from the multimeter. 4. Refer to your appliance manual to see if the detected amperage matches the operating load of your device. 5. If the amperage reading is lower than it should be, a component may have failed, causing excessive resistance. If the amperage is too high, a component may have failed, causing a short circuit and lowering the resistance.    Modern Appliances are Complex    Most modern appliances have both AC and DC circuits.   l AC circuits power high-load components like motors, heaters, and compressors. l DC circuits are used to control AC circuits. For example, there may be 12V DC and 5V DC circuits powering computers and precision electronics. Computers use low-current wires to monitor high-current AC components and turn them on and off as needed. Therefore, when conducting appliance testing, it can be difficult to know where to start because so many components are interconnected.  

  Impact testing on the heat-proof glass-ceramic surface of an induction hob is crucial to ensure the product's safety, durability, performance, and compliance with industry standards.   WHY? Here’s a more detailed breakdown of why this testing is essential:   1. Safety Preventing Shattering: The glass-ceramic surface acts as a protective barrier between the user and the high-temperature components of the hob. If the surface were to shatter upon impact, sharp glass shards could cause serious injuries. Impact testing simulates real-world scenarios, such as accidentally dropping a heavy pot, to ensure the glass can withstand such forces without breaking. Thermal Safety Considerations: A compromised glass-ceramic surface, such as one with cracks or chips, can become more vulnerable to thermal stress. During cooking, the surface is exposed to rapid heating and cooling, which could exacerbate any existing damage. Ensuring the glass can withstand impact without damage reduces the risk of sudden failure during use, which could lead to exposure of electrical components or even fires.   2. Durability Longevity Under Regular Use: The induction hob is subject to frequent use, where pots and pans are placed, slid, or accidentally dropped on the surface. Impact testing ensures that the glass-ceramic can endure these daily stresses over many years, maintaining its structural integrity and ensuring the hob remains functional for its expected lifespan. Resistance to Micro-Damage: Even minor impacts can cause micro-cracks or chips that might not be immediately visible. Over time, these small imperfections can grow under continued use and thermal cycling, potentially leading to larger cracks or complete failure. Impact testing helps identify and mitigate these risks early in the product development phase.   3. Product Performance Maintaining Cooking Efficiency: The glass-ceramic surface is not only a protective layer but also plays a role in the hob's efficiency by facilitating even heat distribution. Any damage from impacts could affect the smoothness and flatness of the surface, which in turn could interfere with the hob’s ability to heat cookware evenly, leading to poor cooking performance. Ensuring Aesthetic Longevity: Aesthetics are important for consumer satisfaction. A cracked or chipped surface is not only a functional issue but also diminishes the visual appeal of the appliance. Impact testing helps ensure that the surface remains free from visible damage over time, maintaining the product's premium appearance.   4. Compliance with Industry Standards Adherence to Safety Regulations: Various regulatory bodies set safety standards for household appliances. For induction hobs, these standards often include requirements for impact resistance to ensure consumer safety. Impact testing is necessary to certify that the product meets these regulatory standards, which is often a prerequisite for entering specific markets. Quality Assurance Certification: Many manufacturers aim for quality certifications (like ISO or UL certifications) that require rigorous testing, including impact resistance. Achieving these certifications can be a critical part of the product’s marketability and consumer trust.   5. Consumer Confidence Building and Maintaining Trust: A product that is proven to withstand real-life usage scenarios, including accidental impacts, fosters consumer confidence. Customers need assurance that their investment in an induction hob is sound, and that the product will not fail under normal or even occasional rough handling. Successfully passing impact tests is a key factor in building this trust. Brand Reputation and Competitive Advantage: In a competitive market, brands that emphasize the durability and safety of their products through rigorous testing can differentiate themselves. Impact resistance is often highlighted in marketing as a sign of superior build quality, giving consumers an additional reason to choose a particular brand or model.  

          Temperature Test on Household Appliances Temperature testing is a crucial process in evaluating the safety and performance of household appliances. This test ensures that the appliance operates within safe temperature limits during normal use and under fault conditions, preventing overheating that could lead to fires, electrical failures, or damage to the appliance.   Why Temperature Testing is Important ？ 1. Safety Compliance: Regulatory standards require appliances to maintain safe temperatures to avoid the risk of burns, fires, or component failure. 2. Performance Assurance: Ensures that the appliance performs efficiently and reliably under various conditions. 3. Durability Testing: Helps assess the longevity of the appliance by testing it under stress conditions, such as prolonged use or exposure to higher temperatures.   How Temperature Testing is Conducted ？ 1. Setting Up the Appliance: The appliance is set up in a controlled environment, replicating typical usage conditions. 2. Thermocouples Placement: Thermocouples or temperature sensors are placed at critical points, such as near heating elements, on the outer casing, and around electronic components. 3. Test Voltage Application: The appliance is powered on, and different operating cycles are tested. For heating appliances, maximum operational settings are often used. 4. Data Collection: Temperatures are recorded over time, with particular attention to any areas that approach critical limits. 5. Fault Condition Simulation: In some tests, fault conditions are simulated (e.g., blocked ventilation or power surges) to see how the appliance handles stress.   Evaluating the Results Comparison to Standards: The measured temperatures are compared against industry standards and regulatory limits to ensure compliance. Safety Margins: Adequate safety margins are required to ensure the appliance remains safe under all conditions. Component Integrity: The test also checks for signs of component degradation, melting, or other damage caused by excessive heat.   Belw is the Temperature Test Instrument of Household Appliances Temperature Rise Test Corner  Can be customized with Various Dimensions 600X600X1000mm 800X800X1000mm 1000x1000x1200mm   Testing method： 1. Place the test sample on the test corner as required and connect it to the power source. 2. Lead the thermocouple through the wire channel to the terminals on the back of the temperature measuring instrument on the side plate. 3. Measure the temperature of each point on the current measurement surface.  

           The Insulation Resistance Test Safety tests are essential and form a crucial part of every final inspection for electrical products.   WHY? Safe insulation is essential for ensuring electrical safety. It prevents users from touching live conductors and stops short circuits from occurring between conductors or to the equipment’s housing. If a short circuit does happen, it could lead to a life-threatening current flowing through the user if they touch the housing. The protective earth conductor is supposed to prevent this, but it could fail, and even then, it only mitigates the effect, not the cause. To avoid these risks, insulation must be flawless. You must confirm and document this by conducting an insulation resistance test before the electrical product is released. This test is mandatory for every unit—meaning that every single electrical product you put on the market must pass an insulation resistance test.   WHERE? It's a bit more complex than with the protective earth conductor, for example. Essentially, there must be good insulation between current-carrying conductors or between these conductors and housing parts. Typically, this is achieved by insulating the electrical conductors to prevent dangerous contact, meaning they are covered with an insulating material. However, this protective sheath must be removed when the electrical conductor is connected to other electrical components. At these points, insulation is maintained by ensuring a safe distance. Here, safety is ensured through clearance and creepage distances. Additionally, current-carrying conductors can be insulated from each other using methods like casting compounds, insulating foils, or solid materials. When is each type of insulation used? This depends on the design of the electrical product and specific requirements, such as high temperature or mechanical stress. It becomes clear that the insulation requirements and designs in a luminaire, an electric iron, an electric motor, or a high-voltage insulator in a power station are vastly different. This diversity leads to quite complex electrotechnical insulation structures in each case.   HOW? Since insulation is related to voltage, the insulation resistance test is conducted using a defined test voltage level. This voltage can either be gradually increased or applied directly at its full magnitude to the device being tested. The purpose of the test is to measure the current and then calculate the insulation resistance, which is the key criterion for evaluating the insulation's effectiveness. The insulation resistance must meet or exceed a specified minimum value. The minimum required insulation resistance can vary depending on the product and region. Therefore, it's essential to follow the testing parameters specified in the relevant standards for the product and region.    

DIN0620-1 VDE Steckerstift-Mess- und Prüfwerkzeuge Deutsche Norm Steckdosen- und SteckdosenprüfgeräteVDE DIN 0620-1 Prüfgeräte-Liste: Abbildungsnummer Projektname Anzahl DIN-VDE0620-1-Lehre1 Steckdose R Lehre (5.0, 5.8, 6.0) 3 DIN-VDE0620-1-lehre2 Mindestöffnungsweite und Mindestabzugskraft der Kontaktbuchse 2 DIN-VDE0620-1-Lehre3 Bipolare Steckerkraft 1 DIN-VDE0620-1-Lehre4 Bipolarstecker mit Erdungskontakt Einführseitige Kraft 1 DIN-VDE0620-1-Lehre5 Zur Prüfung des ersten Kontaktanschlussintervalls 1 Satz / 4 Teile DIN-VDE0620-1-Lehre6 Stiftdurchmesser 1 Satz / 4 Teile DIN-VDE0620-1-Lehre7 Stiftabstand 1 / 2 Kombination DIN-VDE0620-1-Lehre8 Maximale Öffnungsweite der Kontaktbuchse 1 DIN-VDE0620-1-Lehre9 Austauschbarkeitstest Steckerlehre 1 DIN-VDE0620-1-Lehre10-A Unmöglichkeit des Kontakts des einpoligen Kontaktlochs A 1 DIN-VDE0620-1-Lehre10-B Unipolare Kontaktlochkontakte nicht die Möglichkeit von B 1 DIN-VDE0620-1-Lehre11 Kein zweipoliger Stecker kann ohne Erdungskontakt eingesteckt werden 1 DIN-VDE0620-1-Lehre12 Möglichkeit des einpoligen Einsteckens (einschließlich 250 Gramm und 1000 Gramm Gewicht und Positionierungsrahmen) 1 Satz / 4 Teile DIN-VDE0620-1-Lehre13 Nach normalem Betriebstest des Schutzes von unter Spannung stehenden Teilen, die sich im Inneren der Tür befinden, können nicht berührte Sonden 1 Satz DIN-VDE0620-1-Lehre14 Erdungstest auf beiden Seiten 1 DIN-VDE0620-1-Lehre15 Schutz von unter Spannung stehenden Teilen im Inneren der Tür und Verstärkung des Schutzes von unter Spannung stehenden Teilen der Steckdose kann nicht mit der Sonde berührt werden 1 Satz DIN-VDE0620-1Fig15 Lehre 1 DIN-VDE0620-1-Lehre16a Maximale Abzugskraft Stecker (16a) 1 DIN-VDE0620-1-Lehre16d Maximale Abzugskraft Stecker (16d) 1 DIN-VDE0620-1-Lehre17 Lehre17 1 DIN-VDE0620-1-Lehre18 Lehre18 Prüfgerät 1 DIN-VDE0620-1-EN50075 Austauschbarkeitstest Steckerlehre 1 DIN-VDE0620-1-49440-L1 49440-L1- auf der IPX4-Teststeckdose 1 DIN-VDE0620-1-49440-L2 49440-L2- auf der IPX4-Teststeckdose 1 DIN-VDE0620-1-49440-L1-L2 Bipolar geerdeter Steckerdurchmesser-Prüfgerät und Testausrüstung 1 Satz / 3 Teile DIN-VDE0620-1-Bild15 Prüfdruckgerät 1 Satz DIN-VDE0620-1-Bild14 Bild14 Lehre 1 Satz DIN-VDE0620-1-Bild43 Bild43 Lehre 1 Satz / 2 Teile

  IEC60529 Access test probe kit includes the follow: · Ø50mm Access Sphere Probe (Test probe A) · Jointed Finger Probe(Test probe B) · 2.5 mm Test Rod (Test probe C) · 1.0 mm Test Wire(Test probe D)   IP1X Probe A /Test Probe A 1. According to : IEC61032:1997 /IEC60529:2001 and UL 2.IP1X Probe A (Test Probe A) is necessary appliance for domestic and similar electrical appliance of against electric shock protection test. Technical Parameters: l 1. Ball Diameter: 50mm l 2. Baffle Plate Diameter: 45mm l 3.Baffle Plate Thickness:4mm l 4. Handle Diameter: 10mm l 5. Handle Length :100mm l 6.According to IEC61032 figure 1 (the Test probe A) Jointed Finger Probe B, IP2X 12mm test finger 1. Product Introduction: It meets the requirements of IEC60065, IEC 60335-1, IEC 60529, IEC61032 Figure 2 Test Tool B, IEC950 Figure 2A, IEC60884, Test Tool B, UL507, EN60529 Figure 1, UL1278 Figure 8.4 and other standards. Inspection for protection against finger touch or inspection against electric shock. Specimen range: easily accessible live parts or mechanical parts of the enclosure. 2. Specification: ①　Diameter of curved finger: 12 mm ②　Bending finger length: 80mm (total length of three sections) ③　Diameter of baffle: 50mm ④　Baffle length: 100mm ⑤　Reference standard: IEC60065, IEC 60335-1, IEC 60529, IEC60884-1,    IEC60950, IEC61032, IEC69745-1   IP3X Test Probe C 1. Product overview: The test probe C meets the requirements of IEC 60529 & IEC61032 standards. It is used to simulate tools and metal wires in the IP protection test. It is mainly used for the test of the first characteristic number 3 and the additional letter C of the IP protection level test. In the test requirements for preventing access to dangerous parts, the test probe C needs to have a thrust of 3±0.3N 2. Technical parameters: ①　Probe length: 100mm ②　Probe diameter: 2.5mm ③　Ball diameter: 35mm ④　Handle diameter: 10mm ⑤　Handle length: 100mm ⑥　According to IEC61032 Figure 3 (Test probe C), IEC60529   IP4X Test Probe D Basic Introduction: 1.According to: IEC61032:1997/IEC60529:2001 AND UL 2.IP4X Test Probe D ( Test Probe D) is a necessary appliance for domestic and similar electrical appliance of against electric shock protection test. Technical parameters 1.Test Probe Length :100mm 2. Test Probe Diameter:1.0mm 3.Dam- sphere Diameter:35mm 4.Handle Diameter:10mm 5.Handle Length 100mm 6. According to IEC61032 figure 4 (the Test probe D)

Standards: UL22, Sixth Edition, Figure 10.1 Articulate probe with web stopUL48, Fifteenth Edition, Figure 4.3 Articulate probe with web stopUL73, Tenth Edition, Figure 11.1 Articulate probe with web stopUL153, Twelfth Edition, Figure 23.1, Accessibility probeUL399, Seventh Edition, Figure 6.1 Articulate probe with web stopUL474, Ninth Edition, Figure 4.1 Accessibility probeUL499, Thirteenth Edition, Figure 6.2 Articulate probe with web stopUL507, Ninth Edition, Figure 9.2 Articulate probe with web stopUL508, Seventeenth Edition, Figure 6.4 Articulate probe with web stopUL508C, Third Edition, Figure 6.4 Articulate probe with web stopUL982, Sixth Edition, Figure 7.1 ProbeUL998, Fourth Edition, Figure 2 – Articulated probe with web stopUL1012, Eighth Edition, Figure 8.1 Articulate probe with web stopUL1017, Eighth Edition, Figure 2 – Articulated accessibility probeUL1026, Sixth Edition, Figure 6.2 Accessibility probeUL1082, Sixth Edition, Figure 7.2 Accessibility probeUL1083, Sixth Edition, Figure 7.2 Accessibility probeUL1206, Fourth Edition, Figure 8.1 Articulate probe with web stopUL1278, Third Edition Figure 8.3, Articulate probe with web stopUL1310, Sixth Edition, Figure 16.2 Articulate probe with web stopUL1598, Third Edition, Figure 19.22.1 Articulate probe with web stopUL1727, Fifth Edition, Figure 9.1 Articulated probe with web stopUL1993,Figure 9.3 Articulate test probeUL5085-1, First Edition, Figure 1 Articulate probe with web stopUL8750, First Edition, Figure 7.1 Articulate probe with web stopUL60065, Seventh Edition, Figure 18 DU – Articulated finger probeUL60335-1, Fourth Edition,, Figure 12DV – Articulated Probe with Web StopUL60950, Second Edition, Figure NAF.1 – Articulated accessibility probe Application: Protection for electrical equipment enclosures during testing. UL test finger is essential for safety testing of household appliances. Test on: Accessible enclosure parts that are electrically live or mechanical. Component:  Nylon handle+probe, made according to standard diagram

Standard:  Clause 24.1 of GB2099.1-2008 and Figure 22-26 GB16915.1-2014  IEC884-1 Figure 22-26  GB2423.55  IEC60068-2-75 Application: Mechanical strength testing of electrical accessories for household and similar purposes such as plugs, receptacles, surface-mounted installation boxes, screw-on caps, cover plates, switches, etc. Test on:  Plugs, sockets, surface-mounted installation boxes, threaded pressure caps, cover plates, switches, and other electrical accessories. Functionality: The bracket is installable with vertical and horizontal mobility, and adjustable for impact angle. This device is a low-energy pendulum impactor for impacts up to 2J.       

Ingress Protection (IP) Rating Test The Ingress Protection (IP) Rating Test is used to evaluate the ability of an enclosure to protect equipment from external substances such as dust and moisture.   This test is designed to determine the capability of a device to function normally under various environmental conditions, particularly when exposed to dust and water. It is widely applied in electronic devices, electrical enclosures, lighting equipment, and other products to ensure their reliability and durability in specific use environments.   Composition of IP Ratings IP ratings consist of two digits, where the first digit represents the level of protection against solid objects (e.g., dust), and the second digit represents the level of protection against liquids (e.g., water). l First digit (0-6): Indicates the level of protection against solid particles such as dust. l Second digit (0-9): Indicates the level of protection against liquids such as water.   Solid Particle Protection (First Digit) Digit Protection Description 0 No protection 1 Protection against solid objects larger than 50 mm (e.g., back of the hand) 2 Protection against solid objects larger than 12.5 mm (e.g., fingers) 3 Protection against solid objects larger than 2.5 mm (e.g., tools, thick wires) 4 Protection against solid objects larger than 1.0 mm (e.g., most wires) 5 Dust protection (limited ingress of dust permitted, but not enough to interfere with operation) 6 Fully dust-tight (no ingress of dust)   Liquid Protection (Second Digit) Digit Protection Description 0 No protection 1 Protection against vertically falling water drops 2 Protection against water drops when the device is tilted up to 15° 3 Protection against spraying water (up to 60° from vertical) 4 Protection against splashing water from any direction 5 Protection against low-pressure water jets from any direction 6 Protection against powerful water jets from any direction 7 Protection against immersion in water up to 1 meter for 30 minutes 8 Protection against prolonged immersion under conditions specified by the manufacturer 9K Protection against high-pressure, high-temperature water jets   Specific Testing Processes for IP Rating 1.  Dust Protection Test: l A specialized dust chamber is used to generate a specified amount of dust, in which the device is placed. l The test duration and conditions are set according to the product's required protection level. For high protection levels (e.g., IP6X), the device must be exposed in a sealed dust environment for a specific time, ensuring no dust ingress. Water Protection Test: l Water protection tests use various water sources, such as water spray devices, water flow setups, or even direct immersion of the device in water. l Test conditions include water pressure, temperature, spray angle, and duration, depending on the required protection level. For example, an IPX7 test requires the device to be submerged in 1 meter of water for 30 minutes, while an IPX9K test requires it to be subjected to high-pressure, high-temperature water jets.   Evaluation and Results: l After testing, the device is evaluated to determine whether dust or water has entered the enclosure. This evaluation is done through visual inspection, electrical performance testing, or other methods to ensure the device's functionality and integrity are maintained. l Based on the test results, the device is assigned the appropriate IP rating.   Application Areas l Consumer Electronics: Devices like smartphones and smartwatches typically have some level of water and dust protection, commonly rated IP67 or IP68. l Industrial Equipment: Control cabinets, sensors, and switchgear, which often need to operate in harsh environments, typically require higher IP ratings. l Lighting Equipment: Especially outdoor lighting fixtures, which need to have high levels of water protection, such as IP65 or higher.   IP rating tests help manufacturers ensure their products are safe and durable in their intended environments, and they also serve as an important reference for consumers when selecting equipment.

  Application: Testing of the switching capacity and normal operating life for switches in household and similar fixed electrical installations. It also can be applied for Testing the breaking capacity and normal operating life of plugs and sockets . Test on: Switches for household and similar fixed electrical installations Plugs for household and similar use Sockets/Outlets: "Sockets for household and similar use Functionality: A load cabinet is specifically designed to test the performance of electrical equipment by simulating various load conditions. This allows for the evaluation of the durability and functionality of the equipment. 1.  Operational Control Panel Ø Panel Surface: The panel features a sandblasted finish to enhance wear resistance. 2.  Control and Display Ø Power Switch: Controls the main power of the load cabinet. Ø Display Meters:  Show the current, voltage, power, and power factor of the powered product. Ø Load Power Switch: Controls the connection and disconnection of the load. Ø Status Indicator Lights:  Display the operating status of various aspects of the equipment. Ø Start and Stop Buttons: Used to start and stop the testing process. Ø Capacitance Selector Switch: Switches between different capacitance values. Ø Load Type Selector Switch: Switches between different types of loads (resistive, inductive, and capacitive). Ø Alarm: Sounds an alert in abnormal conditions. 3.  Control Knobs Ø Voltage Output Adjustment Knob: Adjusts the voltage output for each channel. Ø Current Adjustment Knob: Adjusts the current for each channel. Ø Inductance Adjustment Knob: Adjusts the inductance for each channel. 4.  Multifunctional Load Ø Combined Load Functions:Each load channel has a three-in-one function with resistive, inductive, and capacitive (fluorescent lamp type) loads. Ø Load Type Switch: Allows switching between different types of loads via a selector switch. 5.  Cooling System Ø Cooling Method: Internal strong airflow convection cooling effectively prevents overheating and ensures stable operation of the equipment. 6.  Terminal Connections Ø It is the rear of the load cabinet, allowing connection to a switch and plug socket life tester via wires.  These connections facilitate the output of current, voltage, and power during the testing process.   Technical Specifications: Load Power Supply Three-phase four-wire AC380/50Hz (Single-phase AC220V, three groups in total) Power Load Cabinet Classification Single station (Product code: YW-1109A) Double station (Product code: YW-1109B) Triple station (Product code: YW-1109C) Digital Voltage Meter 0~300V, accuracy ±0.5% Digital Current Meter 0~30A, accuracy ±0.5% Digital Power Meter 0~10KW, accuracy ±0.5% Digital Power Factor Meter 0.3~0.98, accuracy ±0.5% Load Modes Resistive, inductive, capacitive (switchable) Capacitive Load Optional 70uf, 140uf, 7.3uf Load Outputs Selectable for each load output and every other load output Counter 0~999999 times, programmable   Load Power Supply Capacity 3*10KVA Output Current Limit 30A, automatically cut off when exceeded 32A Output Voltage Limit 300V, automatically cut off when exceeded 305V

  Compliance Standards GB4706.24-2000: Safety requirements for household and similar electrical appliances, specific to washing machines. Testing Purpose Primarily used to test the performance and durability of washing machine doors in terms of opening and closing cycles. Features of the Testing Equipment 1. PLC Control and Stepper Motor Drive: Utilizes PLC (Programmable Logic Controller) and stepper motor control to ensure precise and stable testing processes. 2. All-Stainless Steel Manipulator: High durability and precision, ensuring reliability over long-term use. 3. Vacuum Suction Structure: Ensures effective gripping and operation of the washing machine door during testing. 4. TFT True Color LCD Touch Screen: User-friendly interface, easy operation, and allows presetting of various test parameters. 5. Intelligent Control: Capable of precisely setting test angles and speeds to simulate real opening and closing operations. 6. High-Grade Aluminum Alloy Frame: Sturdy and durable, lightweight, and easy to install and maintain. 7. High Versatility: Suitable for testing washing machines of different sizes and types (left-opening and top-opening doors).